Ниво на рамката

Име на продукта: Рамково ниво, монтажно ниво

Има два вида ниво: ниво на рамката и ниво на лентата. Те се използват главно за проверка на изправеността на различни металорежещи машини и друго оборудване, правилността на хоризонталните и вертикалните позиции на монтажа, а също така могат да проверяват малки ъгли на наклон.

Инструкции за използване на рамково ниво:

Когато измервате, изчакайте, докато мехурчетата са напълно неподвижни, преди да вземете показания. Посочената стойност на нивото е стойността на наклона на базата на един метър, която може да се изчисли с помощта на следното уравнение:

Действителна стойност на наклона = индикация на мащаба x L x брой на решетките за отклонение

Например показанието на скалата е 0,02 mm/L=200 mm, с отклонение от 2 решетки.

So: actual tilt value=0.021000 × 200 × 2=0.008mm

Метод за регулиране на нулата:

Place the level on a stable flat plate and wait for the bubbles to stabilize before reading a, then rotate the instrument 180 degrees and place it in its original position to read b. The zero position error of the instrument is 1/2 (a-b); Then, loosen the fixing screws on the side of the spirit level, insert an 8mm hex wrench into the eccentric adjuster, rotate it, and perform zero adjustment. At this point, if it is found that the instrument is tilted 5 degrees forward and backward, and the movement of the level bubble is greater than 1/2 of the scale value, it is necessary t

o rotate the left and right adjusters again until the bubble does not move with the inclined surface of the instrument. Afterwards, it is necessary to check whether the zero position has moved. If the zero position does not move, tighten the fixing screw and adjust it.

Предпазни мерки за нивото на рамката:

1. 1. Преди употреба почистете работната повърхност на инструмента с бензин и я избършете с обезмаслена памучна прежда.
2. 2. Температурните промени могат да причинят грешки в измерването и трябва да бъдат изолирани от източници на топлина и въздух по време на употреба.
3. 3. Отчитането може да се направи само след пълно спиране на мехурчетата (приблизително 15 секунди след поставяне на нивелира върху измервателната повърхност)
4. 4. За да избегнете грешки, причинени от неточна хоризонтална нулева позиция и успоредност на работната повърхност, проверете и регулирайте преди употреба.

Спецификации на ниво рамка：

Precision Frame Level: Key Features & Uses

A precision frame level is the cornerstone of accurate measurement in industrial and workshop settings, designed to deliver unmatched stability and reliability for detecting horizontal and vertical deviations. As a premium category within frame levels, this tool combines robust construction with advanced optical technology, making it indispensable for professionals who demand precision in every project.

Key Features That Define Excellence

1. High-Accuracy Bubble System: Equipped with a calibrated frame spirit level vial, our precision frame spirit level ensures visibility from multiple angles, allowing users to identify even the slightest tilts (as low as 0.02mm/m deviation). The dual-vial design supports both horizontal and vertical measurements, eliminating the need for multiple tools.

2. Durable Construction: Crafted from aircraft-grade aluminum or cast iron, these frame levels resist corrosion, impact, and temperature fluctuations, maintaining accuracy in harsh environments. The reinforced edges protect the vials from damage, extending the tool’s lifespan for long-term value.

3. Multi-Surface Measurement: The rectangular frame design provides four perfectly machined working surfaces, enabling precise checks on flatness, squareness, and alignment across metal, wood, or concrete surfaces. This versatility makes it a go-to choice for machinery installation, woodworking, and structural engineering.

Wide-Ranging Applications

Whether you’re aligning heavy industrial machinery, ensuring the plumb of construction frameworks, or calibrating precision instruments, a precision frame level guarantees reliable results. Its compact size and ergonomic grip also make it ideal for tight spaces, where traditional tools fall short. Professionals in manufacturing, construction, and quality control rely on these frame levels to minimize errors, improve efficiency, and uphold industry standards.

For businesses seeking cost-effective solutions, our level frame pricing balances premium quality with competitive rates, offering bulk discounts and customized models to suit project requirements. Invest in a precision frame spirit level today and experience the difference in measurements that you can trust.

Frame Level Usage Precautions & Error Prevention

Proper handling of a frame level is critical to maintaining measurement accuracy and prolonging the tool’s lifespan. Whether you’re using a standard frame spirit level or a high-end precision frame level, adhering to these precautions ensures reliable results and minimizes errors in industrial, construction, or workshop settings.

1. Pre-Use Inspection & Calibration

Before each use, verify that the frame level’s working surfaces are clean and free of debris—even a speck of dust can cause misalignment. For precision frame spirit levels, check the bubble vial for airtight seals and proper alignment: place the level on a known flat surface, note the bubble position, then rotate it 180°—the bubble should return to the same mark. If not, recalibrate using the manufacturer’s instructions or contact a professional to avoid systematic errors.

2. Environmental Factors to Control

Temperature fluctuations and humidity can affect both the tool’s material (e.g., metal expansion/contraction) and the bubble’s fluid consistency. Store frame levels in a dry, temperature-stable environment, and allow the tool to acclimate to the working temperature for 10–15 minutes before use. Avoid exposing it to direct sunlight or extreme heat/cold, as these can distort measurements and damage the vial.

3. Correct Operation Techniques

When measuring, apply even pressure to all four edges of the frame level to ensure full contact with the surface—tilting or uneven pressure is a common source of human error. For vertical measurements, use the plumb vial (if dual-vial design) and ensure the level is perfectly aligned with the reference edge. In tight spaces, opt for a compact precision frame level with ergonomic grips to maintain stability without overstretching.

4. Maintenance & Storage Best Practices

After use, wipe the frame level with a soft cloth and mild non-corrosive cleaner for metal surfaces to remove oils or residues. Inspect the vials for cracks or fluid leaks regularly—damage to the frame spirit level vial requires immediate replacement. Store horizontally in a protective case to prevent warping of the frame, especially for larger frame levels with longer measurement edges.

5. Common Error Triggers to Avoid

Ignoring Surface Flatness: Always check the base surface for warping before measuring—an uneven surface will render even the best precision frame level inaccurate.
Rushing Bubble Stabilization: Allow 2–3 seconds for the bubble to settle completely before taking readings, especially in vibrating environments.
Neglecting Calibration Cycles: High-precision tools like precision frame spirit levels should be recalibrated annually or after a significant impact to maintain factory-grade accuracy.

By following these guidelines, you not only enhance the reliability of your frame-level measurements but also protect your investment. Proper care can extend the tool’s service life, reducing the need for frequent replacements and optimizing the level frames' pricing value over time. Prioritize these precautions to ensure every measurement is as precise as the tool itself.

Why Choose Our Precision Frame Levels?

At Storaen, we engineer precision frame levels that combine unmatched accuracy with rugged durability and are trusted by professionals in industrial, construction, and workshop settings. Here’s what sets us apart:

1. Uncompromising Precision

Our precision frame spirit level technology detects deviations as fine as 0.02mm/m, critical for aerospace, CNC alignment, and structural checks. The dual-vial design ensures simultaneous horizontal/vertical readings, reducing rework and errors. Trust Storaen for measurements that meet the highest standards.

2. Built for Tough Environments

Crafted from aircraft-grade aluminum with anti-corrosion coatings, our frame levels withstand extreme temperatures, impacts, and chemicals. Reinforced frames protect vials from drops, while precision-machined surfaces maintain micron-level flatness—ideal for steel mills, offshore rigs, and heavy-duty use.

3. User-Focused Design

Ergonomic grips and a lightweight profile make our precision frame levels easy to handle in tight spaces, with high-contrast vials for clear visibility in low light. Four-sided measurement edges adapt to metal, wood, or concrete, delivering versatility without compromise.

4. Quality & Value Combined

Storaen’s level frames pricing offers industrial-grade tools at up to 30% less than competitors, thanks to our direct-to-user model. Bulk orders and custom options provide additional savings, without sacrificing ISO 9001-certified quality or rigorous 12-point inspections.

5. 30+ Years of Expertise

Decades of engineering innovation drive every detail—from surface scraping for precision to thermal aging for stability. Each precision frame spirit level is built to last, ensuring reliability in even the most demanding environments.

Choose Storaen for precision frame levels that deliver accuracy, durability, and affordability. Elevate your workflow today with a tool designed for professionals who refuse to settle for less.